JetMac
Refine Search
Welding,Brazing & Soldering
- Welding
Power Tools
- A great value for money dust collector for industrial or home workshop use. It has a 2.0hp motor driving a fully balanced heavy duty fan/impeller constructed from mild steel and has a rated air flow of up to 1400 cubic feet per minute [+ or - 10 percent, the flow could be lower and is dependent on the length and diameter of your suction pipes].
- It is has top nylon filter bags, the bags measure 500mm in diameter by 850mm deep and are held in place by an over centre clip type steel strap. The collector has a 125mm inlet and is supplied with a Y splitter - 125mm to 2 x 100mm a 100mm so as to facilitate taking dust off two machines at the same time, a 100mm cap is provided in the advent that only one of the 100mm inlets is required.
RM1,800.00
- This dust collector is great low cost option for a workshop when several machines need to be extracted at the same time. It has a 5.0hp motor driving a fully balanced heavy duty fan/impeller constructed from mild steel and has a rated air flow of up to 2500 cubic feet per minute [+ or - 10 percent, the flow could be lower and is dependent on the length and diameter of your suction pipes]. It is has twin top and bottom nylon filter bags, the bags measure 500mm in diameter by 850mm deep and are held in place by an over centre clip type steel strap. The dust collector has a 150 mm inlet and is supplied with a triple splitter - 150 mm to 3 x 100mm.
RM2,820.00
- The Jetmac JI2000 gasoline powered portable generator is powered by a 80cc single cylinder, 4-stroke OHV engine that produces 1600 running watts and 2000 starting watts. Our OHV engine is equipped with a low oil shut-off sensor and designed for long life and easy maintenance. This unit also contains true sine wave inverter technology making it safe to power all of you sensitive electronic devices. This unit is ideal for camping trips, hunting, traveling, tailgating, and light jobs around the house.
RM2,899.00
- The Jetmac JI3500 gasoline powered portable generator is powered by a 171cc single cylinder, 4-stroke OHV engine that produces 3100 running watts and 3500 starting watts. Our OHV engine is equipped with a low oil shut-off sensor and designed for long life and easy maintenance. This unit also contains true sine wave inverter technology making it safe to power all of you sensitive electronic devices. This unit is ideal for camping trips, hunting, traveling, tailgating, and light jobs around the house.
RM3,995.00
RM4,399.00
- This is an ideal table saw for workshop or on site work, with an all up weight of around 50 kilograms this saw can be easily loaded and unloaded to the site from the typical builders vehicle.
- Although saws of this type are usually used for ripping, accurate cross cutting either straight or angled using the sliding carriage [supplied as standard] can be achieved. Other features of this saw are, rear feed off table, dust extraction from both above and below the saw blade.
- The wheel kit [supplied as standard] makes moving the machine around a simple task. A nice feature is the new and improved aluminium rip fence with it's substantial lock down rail. The supplied 24 tooth TCT blade delivers an 85 mm maximum depth of cut.
RM1,480.00
- .350mm Cast aluminium wheels with rubber on rims
- .1.0HP Single phase motor with push button switch
- .Top and bottom precision ball bearing saw blade guides
- .Top saw guide assembly adjusted up and down by handwheel
- .Cast iron, ground finish work table – tilts to 45°
- .Mitre gauge, rip fence and one saw blade provided
- .Fabricated steel frame and body of machine
- .Top and bottom front doors for easy blade changing
- .100mm dust extraction outlet on rear of machine
- .Safety guarding covers saw blade except where wood is cut
- .Rigid heavy gauge steel open leg floor stand
RM2,825.00
- Heavy-duty cast iron lathe bed ensures stability and minimal operating vibration
- .Heavy-duty cast iron headstock and tailstock
- .Powerful motor suitable for continuous operation – with 5 spindle speeds ranging from 500 to 3150 rpm for maximum results
- .Convenient adjustment handle at the front machine side to quickly change speeds
RM1,540.00
- .Latest IGBT inverter technology, DC output
- .High efficiency (85%) and high power factor
- .Portable and lightweight unit
- .Air cooling and high duty cycle up to 60% at maximum output
- .Suitable for acid and basic electrode
- .Light industry and residential application
- .Max. 3.2mm rods continue welding
- .Single phase 240V for widely usage
RM420.00